403: Forbidden
Unauthorized IP Address.
Either disable the IP address whitelist or add your address to it.
If you're editing settings.json, see the 'rpc-whitelist' and 'rpc-whitelist-enabled' entries.
If you're still using ACLs, use a whitelist instead. See the transmission-daemon manpage for details.
明显就是IP地址认证不能通过，但我觉得没有输错呀，有谁能帮帮我，我的settings.json配置如下：
{
"alt-speed-down": 50,
"alt-speed-enabled": false,
"alt-speed-time-begin": 540,
"alt-speed-time-day": 127,
"alt-speed-time-enabled": false,
"alt-speed-time-end": 1020,
"alt-speed-up": 50,
"bind-address-ipv4": "0.0.0.0",
"bind-address-ipv6": "::",
"blocklist-enabled": false,
"dht-enabled": true,
"download-dir": "\/share\/Qdownload\/transmission\/",
"encryption": 0,
"lazy-bitfield-enabled": true,
"message-level": 2,
"open-file-limit": 32,
"peer-limit-global": 240,
"peer-limit-per-torrent": 60,
"peer-port": 51413,
"peer-port-random-high": 65535,
"peer-port-random-low": 49152,
"peer-port-random-on-start": false,
"peer-socket-tos": 0,
"pex-enabled": true,
"port-forwarding-enabled": true,
"preallocation": 1,
"proxy": "",
"proxy-auth-enabled": false,
"proxy-auth-password": "",
"proxy-auth-username": "",
"proxy-enabled": false,
"proxy-port": 80,
"proxy-type": 0,
"ratio-limit": 2.0000,
"ratio-limit-enabled": false,
"rpc-authentication-required": false,
"rpc-bind-address": "0.0.0.0",
"rpc-enabled": true,
"rpc-password": "",
"rpc-port": 9091,
"rpc-username": "",
"rpc-whitelist": "*.*.*.*",
"rpc-whitelist-enabled": true,
"speed-limit-down": 100,
"speed-limit-down-enabled": false,
"speed-limit-up": 100,
"speed-limit-up-enabled": false,
"umask": 18,
"upload-slots-per-torrent": 14 本帖最后由 fttbcm 于 2009-12-29 09:38 编辑
哈哈终于明白了，我是看这个看懂的http://www.hkepc.com/forum/viewt ... 5086&extra=&page=33
具体说来说是在执行share/HDA_DATA/.qpkg/Optware/bin/目录下去启动Transmission时,执行下列操作：(这步很重要)
transmission-daemon -p 9091 -f -T -a *.*.*.* -w /share/HDA_DATA/Qdownload/ -g /share/HDA_DATA/Qdownload/config/
这样就行了。具体请看我的BBS:http://hd2pt.com/viewthread.php?tid=37&extra=page%3D1
http://hdchina.org/user/fttbcm.gif 本帖最后由 p_abing 于 2010-3-10 00:11 编辑
我的无法保存AUTORUN.SH，一输入WQ命令，老提示：ERROR 5 INPUT/OUTPUT。
前面的操作呢，没mount好flash吧 mount -t ext2 /dev/mtdblock5 /tmp/config
这样的命令对吧？ 本帖最后由 p_abing 于 2010-3-10 13:04 编辑
autorun.sh内容：
#!/bin/sh
#Transmission start
echo "/share/HDA_DATA/.qpkg/Optware/lib/" >> /etc/ld.so.conf
ldconfig
export EVENT_NOEPOLL=0
export TRANSMISSION_WEB_HOME=/share/HDA_DATA/.qpkg/Optware/share/transmission/web
/share/HDA_DATA/.qpkg/Optware/bin/transmission-daemon -g /share/HDA_DATA/Qdownload/config/ > /share/HDA_DATA/Qdownload/debug_tm.txt
#Ctrl+O WriteOut
chmod +x /tmp/config/autorun.sh
# And finally umount
umount /tmp/config
始终无法保存！不知道什么问题。出现23楼图片中的错误提示。 前面的操作呢，没mount好flash吧
rnir 发表于 2010-3-10 07:59 http://nas1.cn/images/common/back.gif
看来ERROR 5 INPUT/OUTPUT确实是mount的问题。
但是我已经按http://wiki.qnap.com/wiki/Running_Your_Own_Application_at_Startup
的说明：
TS-109, TS-109P, TS-119, TS-209, TS-209P, TS-219, TS-409 (Marvell ARM), TS-419P: Mount the config ramblock /dev/mtdblock5:
# mount -t ext2 /dev/mtdblock5 /tmp/config来加载FLASH了啊。问题到底出在什么地方？ 注意#不是命令的一部分 #是注释，不影响vi的保存。我估计是mount的问题。 当然也可能那个方法不适用最新版本的固件，你可以到官方论坛上去转转 固件是3.2.3的。可能是固件问题。官网上问了，但是说我是vi命令的问题，我试了，命令肯定没问题，看来还是固件的问题可能性大。 解决了，见：http://nas1.cn/thread-2710-1-1.html mark.............. dingdingding...zourenlo .na ji fen 11111dsfsdfsdfsdfdssfsdfsff 嗯，端口映射很重要 请问，系统的qpkg transmission好用吗？
页:
1
[2]